Instructions
SolarFast Class Pack instructions
How to run a SolarFast sun printing class for 30: what is in the pack, applying the dye, making images, exposing and washing.
Download the PDFQuick version
1. Apply SolarFast to the fabric.
2. Pin film in place, or place objects on the coated fabric.
3. Expose to sunlight for 10 to 24 minutes.
4. Wash with SolarFast Wash. You're done: admire your print.
What's in the pack
- 4 bottles (8 oz) of SolarFast dye: Orange, Red, Violet and Blue
- 90 sponges for applying the dye: one per color for each participant (3 per person)
- 5 Film Markers for drawing on film
- Gloves for 30 participants
- 40 sheets of film, 8.5 x 5.5 inches: one for every student plus 10 extra
- 30 sheets of cotton sateen, 8.5 x 5.5 inches, for test prints
- 30 backer boards, 8.5 x 5.5 inches, to insert in t-shirts or back the fabric
- 1 bottle (8 oz) of SolarFast Wash for washing prints
- 150 wire pins for securing film negatives
- Instructions
1. Apply the dye
Use the backer boards as a work surface: put the fabric on a board before applying the dye. On t-shirts, slip a board inside so the dye doesn't bleed through to the back. You can pin the fabric to the board, and the pins also hold objects or film in place.
Apply SolarFast with the sponges, or use a brush or brayer. For hard edges, mask a window the size of your image with masking tape. For brushed edges, just brush the dye out past the edge of your print. SolarFast is thick enough not to bleed: it won't creep under masked areas, and it can be applied through a stencil. An even coat of dye gives the best prints. You can also spray SolarFast from a spray bottle, thinned with up to 50% water.
SolarFast prints must be made while the dye is still wet, but don't oversaturate the fabric. If it's too wet during exposure, condensation can form under the negative and interfere with development. You want the dye absorbed into the fabric, not sitting on top. To avoid overwetting, blot absorbent fabric or paper with a paper towel or rag.
For more ways to apply SolarFast, see SolarFast tips and tricks.
2. Create an image
Use SolarFast as a paint
SolarFast can be used on its own like any other paint, thinned with water or straight from the bottle. Brush it onto fabric and, while it's still wet, take it outside. The color magically appears in the sunlight.
Make prints with objects
SolarFast also makes photograms and shadow prints. Place objects on the coated fabric before exposing it: anything that casts a shadow makes an image. Flat, opaque objects such as keys, tools, leaves or ribbons work best. Use the pins to hold lightweight objects like plants so they don't blow away. You can also lay the film over flat objects and pin it down, which can give deeper colors. There are no rules, so experiment with all kinds of objects. With decent sunlight you'll always get an interesting print.
Make prints from drawings
Draw directly on the film with the Film Markers. Important: the film has a print side and a waterproof side, and the Film Marker only works on the print side, which feels slightly sticky. Wet your fingers and pinch the film to find it. Draw on that side, and keep it face up when printing. The Film Marker dries fast on the film and is completely opaque.
When the drawing is done, lay it on SolarFast-coated fabric on a backer board, waterproof side down and print side up, and pin it in place. Expose to sunlight for 10 to 24 minutes. Bring the print inside before removing the film to reveal the image. You can use the same film for many prints. If dye gets on the waterproof side, wipe it with a damp rag between prints.
Make photographic prints
For permanent photographic prints, use a film negative. Print negatives on the film with any inkjet printer. High-contrast images work best, and density is key: the blackest areas of the negative should be completely opaque, and the lightest areas clear. Layer two negatives for extra contrast, or if your printer puts down less ink. Place the negative waterproof side down (print side up) on the coated fabric and pin it so it stays flat against the fabric.
To turn photos into negatives easily, use the Negative Generator.
3. Expose the print
Expose the coated fabric to sunlight for 10 to 20 minutes, depending on the weather. Prints made early or late in the day, in winter, or on overcast or cloudy days need longer. The best time is the middle of the day, with the sun directly overhead. Use direct sunlight whenever you can. You can watch the color appear, which shows how the exposure is going, but the final result isn't revealed until after washing.
SolarFast develops in UV light. You can expose with artificial light, but the time depends on the bulb's UV output, so do a test first.
4. Wash
After exposing, wash out the undeveloped dye. SolarFast Wash gives the best results. The color isn't fully developed until after washing, and white areas get whiter too. Bring the print inside, out of the sun, before removing the negative. If needed, you can store the print somewhere dark and cool between exposing and washing.
Machine washing is recommended, but you can also hand wash. Use 3 to 4 capfuls (24 ml) of SolarFast Wash and the hottest water possible. When hand washing, keep the print underwater and the water flowing for at least 10 minutes.
Now you're done. Your print is soft, washable, lightfast and permanent.