Instructions

iDye for Natural Fabrics bulk instructions

How to dye with 1 lb iDye for Natural Fabrics on the stove top or in a washing machine, how much dye to use, and how to dye blends.

Download the PDF

Read all the instructions before you start. iDye for Natural Fabrics works on all natural fabrics, but for wool and other animal fibers we recommend Super Fast Acid Dye for Wool. Not all natural fibers are created equal, so results vary with the fabric.

Note: don't use the utensils or pot for food afterwards.

Which iDye?

  • 100% natural fabrics: use iDye for Natural Fabrics.
  • 100% polyester and nylon: use iDye Poly.
  • Polyester blends: use iDye and the matching color of iDye Poly.

For best results

  • Read all the instructions before you start.
  • Use the stove top method for iDye Poly and polyester blends.
  • Stir constantly for even color.

How much dye

Use 3 to 5% dye by dry weight of fabric for the best depth of shade. Use less dye for lighter shades.

Helpful extras: iDye Color Intensifier and iDye Fixative.

Stove top method

1. Fill a stainless steel or enamel pot with just enough warm water for the fabric to move freely. Turn the heat to medium.

2. Add the iDye to the water and bring it to a simmer. Stir until it's fully dissolved.

3. Add the pre-wetted fabric and bring the temperature back to a simmer, just below boiling.

4. For cotton, linen and rayon, dissolve 1 cup (237 ml) of non-iodized salt in hot water and add it to the dye bath. For silk, add ⅓ cup (78 ml) of white vinegar instead. Avoid pouring it directly onto the fabric.

5. Keep it at a simmer and stir frequently for half an hour.

6. Turn off the heat and remove the fabric. Be careful, as the fabric and dye bath will be hot. Wear gloves, since leftover dye can stain skin. Rinse in cool water. For a post-treatment in the final rinse, fill a container with water, add 2 tablespoons of iDye Fixative per pound of fabric and agitate for 2 to 3 minutes.

7. Wash the fabric in cool water with a mild detergent and dry.

Top loading washing machine method

1. Fill the washing machine with just enough very hot water for the fabric to move freely.

2. Add the iDye and agitate for 30 seconds or longer, until dissolved.

3. For cotton, linen and rayon, add 1 cup (237 ml) of non-iodized salt and let it dissolve. For silk, add ⅓ cup (78 ml) of white vinegar instead.

4. Add the pre-wetted fabric.

5. Extend the dyeing time by resetting the wash cycle before the rinse cycle starts. The longer the dyeing time, the darker the color and the better the fixation. We recommend 50 to 60 minutes of dyeing time.

6. For a post-treatment in the final rinse, add 2 tablespoons of iDye Fixative per pound of fabric, and let the cycle finish.

7. Wash the garment in cold water with a mild detergent and dry.

Note: most washers hold some water in the outer tub at the end of a cycle. After dyeing, run a short wash/rinse cycle with your normal detergent to remove any leftover color. If you have hard water, also wipe down the inside of the tub, since soap scum can build up and hold onto dye.

Front loading washing machine method

1. Dissolve the iDye in about two cups of very hot water.

2. For cotton, linen and rayon, dissolve 1 cup of non-iodized salt in about a quart of very hot water.

3. For silk, use ⅓ cup of vinegar instead of salt.

4. Pour the dissolved iDye and the dissolved salt or vinegar into the bottom of the washing machine tub.

5. Add the pre-wetted fabric.

6. Set the machine to the hottest water and longest wash cycle, and extend the cycle if you can. The longer the fabric stays in the wash/dye cycle, the darker the color and the better the fixation.

7. When the wash cycle is done, let the machine finish the rest of the wash/rinse/spin cycle.

8. Wash the garment in cold water with a mild detergent and dry.

Note: clean your washer thoroughly after dyeing. Most front loading washers collect water in the door gasket and hold water in the outer tub. Wipe down the door gasket carefully and run a short cycle with your normal detergent. Your washing machine manual may have cleaning instructions.

Cotton and silk blends

If you're dyeing a cotton and silk blend and aren't sure whether to add salt or vinegar, you have three options:

  • It's not critical: either salt or vinegar will work, so just pick one.
  • Add neither, but use plenty of heat in the dye bath (stove top method).
  • Do two separate dye baths, one with salt and one with vinegar. This is probably best for the darkest colors.

Polyester and nylon blends with natural fibers (stove top)

Polyester is hard to dye and needs very hot water for good color, so we recommend dyeing polyester only on the stove top.

1. Fill a stainless steel or enamel pot with just enough water for the fabric to move freely. Turn the heat to high.

2. Choose the iDye Poly color closest to your iDye for Natural Fabrics color and add both to the water. Add iDye Color Intensifier (14 ml per pound of fabric) and bring to a simmer. Stir until dissolved.

3. Add the pre-wetted fabric and bring to a rolling boil.

4. Add 1 cup (237 ml) of non-iodized salt for cotton, linen and rayon, or ⅓ cup (78 ml) of white vinegar for silk. Avoid pouring it directly onto the fabric.

5. Keep it at a rolling boil and stir frequently for ½ to 1 hour. Stir constantly for even color.

6. Let the fabric cool gradually and rinse until the water is nearly clear. For a post-treatment in the final rinse, fill a container with water, add 2 tablespoons of iDye Fixative per pound of fabric and agitate for 2 to 3 minutes. Wash in cool water with a mild detergent and dry.

Working out dye amounts for blends

When working out how much iDye and iDye Poly you need for 3 to 5% dye, take the fabric blend into account, since not all fabrics are 50/50. For example, to dye 1 lb of 75% polyester and 25% cotton fabric, you'd need about ½ oz of dye in all: 25% (⅛ oz) iDye for Natural Fabrics for the cotton, and 75% (⅜ oz) iDye Poly for the polyester.